| Code | Description (Original Text) | Recommended Action (Paraphrased) | | :--- | :--- | :--- | | 100 | "GREASEUP"通知出现后，若不添加润滑脂 | Add grease and then execute the clearing operation. | | 111 | 停车位置不正确 | Turn off power, check for abnormalities in the thread trimming device or the sewing machine motor. | | 121 | 剪线无法完成 | Turn off power, check the blades of the fixed and movable knives for scratches or damage. | | 130 | 主马达故障 | The spindle motor or its controller is faulty. | | 131 | 同步显示器接触不良 | Turn off power, check the condition of the P11 plug on the motor main board. | | 132 | 发现缝纫机主马达非正常旋转 | Turn off power and check the motor's P11 plug. | | 133 | 缝纫主马达停止位置不良 | Turn off power and check the motor's P11 plug. | | 150 | 缝纫机主马达非正常升温或者温度传感器运转不良 | Check the motor condition. (Can occur with very short stitch cycles). |
| Code | Description (Original Text) | Recommended Action (Paraphrased) | | :--- | :--- | :--- | | 600 | 发生面线断裂 | Press RESET. Then press KEY_STEP_BACK and move the presser foot to continue sewing. | | 690 | 中压脚电机找不到原点 | Failure of the middle presser foot motor or its encoder. | | 691 | 底线夹线马达非正常停止 | Turn off power, clear lint, and check main board sockets P20/P4. | | 693 | 中压脚电机过电流 | Failure of the middle presser foot motor or its control board. | | 697 | 无法检测到中压脚电机运动 | Failure of the middle presser foot motor, its encoder, or its control board. | | 698 | 中压脚电机失控 | Failure of the middle presser foot encoder or control board. |
The Siruba L818F-M1 is a high-speed, single-needle lockstitch industrial sewing machine known for its reliability and precision. However, when electronic or mechanical issues occur, the integrated control panel displays specific error codes to protect the motor and internal components. Understanding these codes is essential for minimizing downtime and maintaining production efficiency.
Introduction The search phrase "siruba+l818fm1+error+list+2021" appears to aim at identifying error codes, diagnostics, or a failure-log specific to the Siruba L818FM1 industrial sewing machine (or its firmware/hardware variants) as documented or discussed around 2021. This essay examines plausible meanings of the query, summarizes likely sources and causes of errors for this model, evaluates troubleshooting approaches, and recommends practical next steps for technicians and managers dealing with such errors.
Return the machine head to its upright, level operating position in the table oil pan. siruba+l818fm1+error+list+2021
Use high-quality oil to ensure the hook and needle bar move freely, preventing ERR4 (feed limit) issues. 4. Where to Find More Help
Disclaimer: Some error codes may vary slightly depending on the specific model variation (e.g., L818F-M1, L818F-NM1). Always consult the official Siruba manual that came with your machine.
Install a dedicated voltage stabilizer if your facility experiences frequent power fluctuations. E02 / Err-02: Undervoltage Protection
Elias wiped a bead of sweat from his forehead. He had spent years mastering the Siruba L818F series | Code | Description (Original Text) | Recommended
There is a communication breakdown between the motor and the control box. Ensure the motor connector is plugged in securely.
Manually turn the handwheel to see if it moves freely.
If the handwheel turns smoothly but the error persists, inspect the motor wiring harness for short circuits. E04 / Err-04: Needle Positioner / Synchronizer Error
Most error codes arise from preventable mechanical or electrical issues. Implement these maintenance practices to minimize disruptions: | | 130 | 主马达故障 | The spindle
Troubleshooting Your Siruba L818-M1 : 2021 Error Code Guide Industrial sewing machines like the (and its variations like the
The control system cannot detect the main motor type or speed. Check motor connectors. Emergency Switch Active
Use a multimeter to test the main electrical outlet voltage. Ensure it matches the machine's rated specification (typically 220V single-phase).
: Remove the needle plate and clean out lint or broken thread bits that could be causing a motor overload (E1).
: Check for mechanical obstructions and ensure all motor plugs are tight. E6: Abnormal Input Signal